KDRKU300/310V
RIVOT Racing
Complete RACE Decoration Kit from RIVOT Racing for Jet Ski Kawasaki Ultr.. More details
0 Item Items
Delivery within 2 to 10 days
Warning: Last items in stock!
Availability date:
Complete RACE Decoration Kit from RIVOT Racing for Jet Ski Kawasaki Ultra 300 and 310 in Green color
ref. KDRKU300/310V
PLEASE SAVE THE PERSONALIZATION FIELDS AT THE BOTTOM OF THE PAGE
The decorative kits are made with ultra-resistant vinyl, as well as reinforced microbead glue and special 100µ thick protection. High Definition Printing.
- Offers optimal protection for your case.
- Under the effect of heat, the vinyl takes shape and adapts to all the contours of your Jet-Ski for greater ease of installation.
- Retains the intensity of its colors for a long time even with strong UV exposure.
ENLARGE THE IMAGE in HD:
Necessary tools :
- A cutter or scissor
- A can of degreaser
- A hair dryer or heat gun (be careful of high temperatures with the gun)
- A raclette
- A soft, clean cloth
Before starting to install your kit, make sure you are in favorable conditions: in a clean and dry place, temperature around 20°C and that you have enough time. Allow 1 to 2 hours to install a kit.
Step 1: Preparing the supports
Clean your fairings several times using a degreaser. It is imperative to remove all traces of glue and grease from plastics even if they are new (silicone residue) because the glue will not adhere properly. Be careful, products such as gasoline, white spirit or “WD40” type products can be effective on certain types of glue, but they are very greasy. Remember to degrease several times if you use it. Do not use window cleaners or acetone.
Step 2: Positioning and gluing
Position the sticker to identify its location. Always start a collage with the rough presentation of the piece to be glued. Little tip: the glue used is in the form of micro beads, this means that you can affix and remove your sticker several times without it sticking permanently. Once you have chosen the appropriate location, all you have to do is scrape the sticker starting from its center which will have the effect of piercing the micro beads and thus triggering the bonding process by polymerization. Once the sticker is in place, remove air bubbles by pressing very hard outwards with a clean cloth and/or a squeegee and/or felt.
Tip: If the part on which you are working has significant relief, consider lightly heating the sticker with a hairdryer, because under the effect of heat the vinyl will take its shape and apply more easily.
Step 3: Finishes
Finally, once the entire kit is installed, lightly warm each part using a hair dryer and apply significant pressure to the entire kit, paying particular attention to sensitive areas, always using with a soft cloth or squeegee, from the inside out.
Step 4: Imperative!
Leave your decoration kit to rest for 2-3 days, no navigation!!! After the pressure exerted, the glue must have time to polymerize and adapt to its new support.
Tip: If you notice an air bubble, proceed as follows:
Prick the bubble squarely in its center using a pin, keep it pressed, heat
the bubble with the hairdryer then remove the pin while continuing to heat. The hot air
dilated will thus evacuate on its own and the bubble will disappear.
28,95€
ODI brand jet ski handles, Rogue V2.1 model in...
27,96€
Hydroturf Mat for Kawasaki Ultra Jet Ski -...
209,95€
14,95€
ODI X-TREME handle Black or gray in 130mm ref....
30,95€
Telescopic emergency oar (from 55 to 107cm)...
30,95€
Additional floating dock for JETSKI. With the...
1 207,95€
Hydroturf saddle cover, HT premier model for...
319,95€
LINQ Retractable Water Ski Mast from Seadoo for...
425,95€
Hydroturf Carpet for Kawasaki 750 SX / SXI Jet...
99,95€
GPS from Garmin, model ECHOMAP UHD 62sv with...
1 359,95€
Original SPARK 2P cover with adjustable...
299,95€
PRO SERIES version Hydroturf mat for Seadoo GTI...
339,95€
Jet Ski First Aid Kit Reference: FAK2
34,95€
Yamaha Speaker Kit for Waverunner FX 2020 and...
559,95€
* required fields