Jet ski accessories

vehiculier

Manufacturers

RACE Graphic Kit for Ultra 300/310 Yellow

KDRKU300/310J

RIVOT Racing

Complete RACE Decoration Kit from RIVOT Racing for Jet Ski Kawasaki Ultr.. More details

Delivery within 2 to 10 days

449,95€ tax incl.

More info

Complete RACE Decoration Kit from RIVOT Racing for Jet Ski Kawasaki Ultra 300 and 310 in Yellow color

Ref. :KDRKU300/310J



PLEASE SAVE THE PERSONALIZATION FIELDS AT THE BOTTOM OF THE PAGE

The decorative kits are made with ultra-resistant vinyl, as well as reinforced microbead glue and special 100µ thick protection. High Definition Printing.

- Offers optimal protection for your case.
- Under the effect of heat, the vinyl takes shape and adapts to all the contours of your Jet-Ski for greater ease of installation.
- Retains the intensity of its colors for a long time even with strong UV exposure.


ENLARGE THE IMAGE in HD:


Necessary tools :
- A cutter or scissor
- A can of degreaser
- A hair dryer or heat gun (be careful of high temperatures with the gun)
- A raclette
- A soft, clean cloth

Before starting to install your kit, make sure you are in favorable conditions: in a clean and dry place, temperature around 20°C and that you have enough time. Allow 1 to 2 hours to install a kit.


Step 1: Preparing the media
Clean your fairings several times using a degreaser. It is imperative to remove all traces of glue and grease from plastics even if they are new (silicone residue) because the glue will not adhere properly. Be careful, products such as gasoline, white spirit or “WD40” type products can be effective on certain types of glue, but they are very greasy. Remember to degrease several times if you use it. Do not use window cleaners or acetone.


Step 2: Positioning and Gluing
Position the sticker to identify its location. Always start a collage with the rough presentation of the piece to be glued. Little tip: the glue used is in the form of micro beads, this means that you can affix and remove your sticker several times without it sticking permanently. Once you have chosen the appropriate location, all you have to do is scrape the sticker starting from its center which will have the effect of piercing the micro beads and thus triggering the bonding process by polymerization. Once the sticker is in place, remove air bubbles by pressing very hard outwards with a clean cloth and/or a squeegee and/or felt.

Tip: If the piece on which you are working has significant relief, consider lightly heating the sticker with a hairdryer, because under the effect of heat the vinyl will take its shape and apply more easily.


Step 3: Finishes
Finally, once the entire kit is installed, lightly warm each part using a hair dryer and apply significant pressure to the entire kit, paying particular attention to sensitive areas, always using with a soft cloth or squeegee, from the inside out.


Step 4: Imperative!
Leave your decoration kit to rest for 2-3 days, no navigation!!! After the pressure exerted, the glue must have time to polymerize and adapt to its new support.


Tip: If you notice an air bubble, proceed as follows:
Prick the bubble squarely in its center using a pin, keep it pressed, heat
the bubble with the hairdryer then remove the pin while continuing to heat. The hot air
dilated will thus evacuate on its own and the bubble will disappear.

Accessories

Customers who bought this product also bought:

  • Reinforced waterproof pouch
    Reinforced...

    Topoplastic reinforced waterproof pouch...

    16,95€

  • Buoy or paddle repair kit
    Buoy or...

    Buoy or paddle repair kit from JOBE JOBE MULTI...

    18,95€

  • Super Degreaser 600ml
    Super...

    Cleaner and Super Degreaser 600ml Reference:...

    5,95€

Other products in the same category

  • RACE Graphic Kit for Kawasaki 15F Jetski Red
    RACE...

    Complete RACE decoration kit from RIVOT Racing...

    399,95€

  • Seadoo 295500554 whistle for jet ski
    Seadoo...

    BRP Yellow Whistle ref. 295500554

    11,95€

  • Plastic fairing kit in colors for SPARK
    Plastic...

    Seadoo Spark Panel Set (8 Colors to Choose...

    463,95€

  • Side protector for Seadoo Spark jet ski
    Side...

    Side protector for Seadoo Spark watercraft...

    201,95€

  • 30L/min Ball Transfer Pump
    30L/min...

    30L/min Ball Transfer Pump Ref: PDTAB30L

    18,95€

  • Rinse kit for Seadoo Spark jet ski
    Rinse kit...

    Rinse Kit for Seadoo Spark ref. 295100555

    46,95€

  • RRP X Lite series 28.6mm steering box
    RRP X Lite...

    RRP (Rick Roy products) X-lite Series Steering...

    299,95€

  • Cover (HT) RXT230/300 & Wake Pro 230 (18)
    Cover (HT)...

    Hydroturf saddle cover, HT premier model for...

    499,95€

  • Explorer LinQ 100L bag for Seadoo jet ski
    Explorer...

    100 liter Explorer LinQ bag for Seadoo...

    509,95€

  • Jettrim 4-piece mat for Kawa. SXR 800
    Jettrim...

    Jettrim mat 4 pieces for Kawasaki SXR 800 hand...

    309,95€

Product customization

After saving your customized product, remember to add it to your cart.

Text

loader

* required fields