Jet ski accessories

vehiculier

Manufacturers

RACE Graphic Kit for Kawasaki 15F Jet Ski Yellow

KDK15FRJ

RIVOT Racing

Complete RACE decoration kit from RIVOT Racing for Jet Ski Kawasaki STX.. More details

Delivery within 7 days

399,95€ tax incl.

More info

Complete RACE decoration kit from RIVOT Racing for Jet Ski Kawasaki STX 15F in Yellow color

ref. KDK15FRJ



THANK YOU FOR SAVING THE CUSTOMIZATION FIELDS AT THE BOTTOM OF THE PAGE

The decorative kits are made with an ultra resistant vinyl, as well as a reinforced microbead glue and a special 100µ thick protection. High Definition printing.

- Provides optimal protection for your case.
- Under the effect of the heat, the vinyl takes shape and adapts to all the contours of your Jet-Ski for greater ease of installation.
- Retains the intensity of its colors for a long time even with strong UV exposure.


ENLARGE IMAGE in HD:


Necessary tools :
- A cutter or chisel
- A spray of degreaser
- A hair dryer or a heat gun (beware of high temperatures with the gun)
- A raclette
- A soft and clean cloth

Before starting to install your kit, make sure you are in favorable conditions: in a clean and dry place, temperature around 20 ° C and that you have sufficient time. Allow 1 to 2 hours for the installation of a kit.


Step 1: Preparation of the supports
Clean your fairings several times using a degreaser. It is imperative to remove all traces of glue and fatty substances from the plastics even if they are new (silicone residues) because the glue will not adhere properly. Be careful, products like gasoline, white spirit or “WD40” type products can be effective on certain types of glue, but they are very greasy. Remember to degrease several times if you use it. Do not use window cleaners or acetone.


Step 2: Positioning and gluing
Position the sticker to mark its location. Always start a gluing by the rough presentation of the piece to be glued. Little tip: the glue used is in the form of micro balls, this means that you can affix and deposit your sticker several times without it sticking permanently. Once you have chosen the appropriate location, all you have to do is scrape the sticker starting from its center, which will have the effect of piercing the micro balls and thus triggering the polymerization bonding process. Once the sticker is in place, remove any air bubbles by pressing very strongly outwards with a clean cloth and / or a squeegee and / or felt.

Tip: If the part on which you are operating has significant relief, consider heating the sticker slightly with a hair dryer, because under the effect of the heat the vinyl will take its shape and will be applied more easily.


Step 3: Finishes
Finally, once the whole kit is installed, warm each part slightly using a hair dryer and apply significant pressure to the entire kit, paying particular attention to sensitive areas, always using with a soft cloth or squeegee, from the inside to the outside.


Step 4: Imperative!
Leave your decoration kit to rest for 2-3 days, no navigation !!! After the pressure exerted, the glue must have time to polymerize and marry its new support.


Tip: If you notice an air bubble, do the following:
Prick the bubble frankly in its center using a pin, keep it pressed, heat
the bubble with the hair dryer then remove the pin while continuing to heat. Hot air
dilated will thus evacuate on its own and the bubble will disappear.

Accessories

Other products in the same category

  • Seadoo Spark Jet Ski Key
    Seadoo...

    seadoo Spark key (non DESS ) ref. 278002843 The...

    65,95€

  • ODI Vans V2.1 135mm Iridescent Purple Grips
    ODI Vans...

    ODI brand handles for jet skis, Vans V2.1...

    35,95€

  • 40L Yamaha cooler for VX and GP1800 jetski
    40L Yamaha...

    40L cooler designed by Yamaha for VX and GP...

    257,95€

  • JETPILOT grappling anchor for jet ski
    JETPILOT...

    JETPILOT 1.5kg grapple anchor kit Jetpilot...

    72,95€

  • Roll of 1m x 1.50m marbled royal blue
    Roll of 1m...

    Hydroturf carpet roll of 1m x 1.50m for jet ski...

    89,95€

  • Seat cover for GP 760/800/1200
    Seat cover...

    Hydroturf saddle cover for Y amaha jet ski...

    239,95€

  • Jettrim mat 8 pieces for HSR S4 arm jet
    Jettrim mat...

    Jettrim mat 8 pieces for HSR Benelli S4 arm jet...

    529,95€

  • 12V socket for Seadoo jet ski
    12V socket...

    12V socket for Seadoo GTX and RXT without...

    64,95€

  • Ultra 310R & 310X SE seat cover (14+)
    Ultra 310R...

    Hydroturf seat cover for Kawasaki Ultra 310 R &...

    289,95€

  • DESS RIVA RF key for Seadoo jet ski (15-24)
    DESS RIVA...

    RF DESS key programmed from RIVA Racing for...

    74,95€

Product customization

After saving your customized product, remember to add it to your cart.

Text

loader

* required fields