Subcategories
- For 4-stroke Seadoo watercraft with a 1494 cubic centimeter engine: (see the correspondence table at the bottom of the page) - Solas Concord or Dynafly Series propeller, in high quality stainless steel and polished finish for better fluidity and less turbulence in the turbine. - Optimized for the best performance in both acceleration and speed.
COVERCRAFT TRANSPORT COVER for Seadoo watercraft Reference: COVERCRAFT-S
Worx Starr / Stop ITC control switch for Seadoo 4 stroke Ref: WR06013
Worx brand IBR / ITC control switch for Seadoo 4 stroke Ref: WR06012
RIVA Racing gear release box for Seadoo 255 / 260 / 300 watercraft (from 2011 to 2015) Ref: RS11090-SCOM-11
IDIARTEC sand filter Ref: IDT-FAS Filter housing in marine quality aluminum machined from mass with stainless steel filter calibrated to stop impurities which risk clogging the engine cooling circuit. Delivered with straight and elbow brass fittings.
159mm impeller ring for seadoo 215 / 255 / 260 / 300 ref. RS33-159-SRX
WISECO piston for seadoo side 100.50mm ref. : 40038M10050
EASY RIDER Reinforced Front Engine Mount for Seadoo 4-stroke watercraft Ref: RS-4262
WORX brand IBR control lever for Seadoo 4 stroke Ref: WR06011
WORX brand electronic accelerator lever for Seadoo 4 stroke Ref: WR06010
WORX Racing shovel scoop for seadoo watercraft from 2009 and above with an S3 hull ref. : WR235
Riva thermostat kit for seadoo RXT/GTX -SC/RXP Ref: RS1015
RIVA Racing reinforcement for Seadoo 215, 255, 260 and 300 watercraft intake manifold Reference: RS12050-IMG-1
Gasket Technology Top End Gasket Kit for SeaDoo 4 Tec 1500cc All Models Watercraft
Reinforced Turbine Shaft from EASY RIDER with propeller housing close to -2mm for Seadoo 4-stroke watercraft Ref: RS-4926
RIVA VALVE LIFT TOOL FOR SEADOO RXP/RXT/GTX-SC Ref: RS19050-VCT
PRO-SERIES cylinder head gasket from Riva Racing for Seadoo 1500cc watercraft from 2005 to 2017 Reference: RS10050-CHG-1503
Ring set for 130mm Forged Piston for 1730cc engine from EASY RIDER for Seadoo Watercraft Sold individually and for the RS-3056 piston kit Reference: RS-3057
RIVA Oil Vapor Canister and Breather Kit for Seadoo RXP 215, RXT 215, RXP-X 255, RXT-X 255, GTX 4 tec, RXP-X 260, all models of RXT & GTX unsuspended, RXP-X 300, RXT-X 300, GTX Ltd 300, RXT 230, GTX 155, GTR 230, GTR-X 230 Reference: RS19050-BCC-6
IDIARTEC Fixed or Cushioned Column for Sea-doo jet-ski in Aluminum or Black version depending on the size Reference: IDT-CSRXP/RXT Seadoo RXP / RXT column
RIVA INTAKE PIPE MODIFICATION KIT FOR SEADOO 255 / 260 Ref: RS12080-IMUK
Stainless steel wear ring 159mm Solas for seadoo 215 / 255 / 260 Ref: SRX-HS-159-02
PROX piston kit (piston + segments + pin + circlips) for Seadoo 1500 jet ski ref.: 01.5594.XX
Supports for 2 fuel cans for jet ski Reference: 52-4910
Riva thermostat for Seadoo 4tec Ref: RS1013-50-1
WORX RACING Free Exhaust for Seadoo 4 tec watercraft before 2016 (except GTX from 2002-03) Ref: WR04027
Racing exhaust spacer from RIVA Racing for Seadoo Reference: RS18050-ERP
High performance injector from RIVA Racing by Bosch for Seadoo brand watercraft from 2004 to 2017 Reference: VT1100-INJ
Rear exhaust outlet kit from RIVA Racing for Seadoo brand watercraft from 2010 to 2015 Reference: RS15090-ET
Ring Kit for Forged Piston in 100mm (99.93mm) from EASY RIDER for Seadoo Watercraft Sold individually Ref: RS-3062
COMETIC Reinforced Head Gasket for Seadoo 1500 Available in 101, 102 or 103mm Ref. C6223-101, C6223-102 or C6223-103
3M pre-glued Hydroturf mat for Seadoo RXT 260 and RXT-X 260 (10-16), Wake 215 (10-15), GTX 155 and 215 (12-15) watercraft (except S models) ref. HT885-PSA All Hydroturf Products are made to measure and individually. They require a minimum manufacturing time of 15 working days. They will not be returned or exchanged.
COMPRESSOR CLUTCH DISC KIT FOR SEADOO RXT-X/GTX-SC/RXP-X 08 (255HP) Ref: RS1751-HDW-948
Riva free exhaust kit for seadoo all S3 and T3, including RXT-X 260, IS, AS and RXP-X 260 Reference: RS16090
IDIARTEC reinforced engine mount for Sea-Doo RXT / RXP 260 Ref: IDT-SMRXT
WATCON tool for re-pitching the Propellers ref. IMP-142 for 140 to 142mm propeller ref. IMP-148 for 144 to 148mm propeller ref. IMP-160 for 155 to 160mm propeller
LISLE . ENGINE ALIGNMENT TOOL . ASSEMBLY ALIGN SUPPORT PLATE KIT . ( sea-doo all model )
AQUA SPORT PERFORMANCE 71° thermostat for Seadoo 4 tec 1503cc watercraft ref. : SD-16004
IControl lever from RIVA RACING for Seadoo watercraft equipped with an IBR ref. : RS24090-ICL
Cylinder Protection Block from AQUA SPORT PERFORMANCE for Seadoo 4 tec 1503cc watercraft all models ref. : SD-12025
30" (76cm) handlebar with reinforcement and RIVA Racing foam for Seadoo RXP 300, RXT 300 & GTX 300 2018 and above watercraft Ref: RS207BK-BAR-2
Exhaust spacer from AQUA SPORT for Seadoo 4 tec 1503cc watercraft Reference: SD-16001B
Replacement liner for Seadoo 130 / 155 / 185 / 215 / 255 / 260 Ref: RS10050-SLV-1503
Worx brand start/stop switch for Seadoo Ref: WR06015
Screw-in duckbill set for Seadoo from 2009 and up (sold in pairs) Ref: A7027
EASY RIDER Titanium Intake Valve for Seadoo 4-stroke watercraft all models. Ref: RS-4247
RIVA O2 Sensor Installation Kit for Seadoo 1503 ref. RS15050-SK-O2
Accelerator cable from EASY RIDER for Seadoo 300 watercraft Ref: RS-7300
EASY RIDER Lightweight Racing Exhaust Valve for Seadoo 4-stroke watercraft all models. Ref: RS-4215
70 degree celsius thermostat from WORX Racing for Seadoo 4 Tec 1503cc watercraft Ref: WR04037
ODI reinforced handlebar for saddle jet Reference: 06013082
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3334
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3052
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3329
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3776
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3780
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3778
Compressor tool 16 teeth (SD 215) Ref: 613-96016